Ask a question about Gliderol Garage Doors in Door & Window Shops. We had issues with the door opening on its own and not closing. We also had the door. ![]() • Glidermatic GRD+ Heavy Duty Automatic Roller Door Operator Installation Instructions and Glidermatic GRD+ Owners Manual Glidermatic GRD+ Installation Instructions & owner’s manual Page 1. • Glidermatic GRD+ Heavy Duty Automatic Roller Door Operator IMPORTANT SAFETY INFORMATION - PLEASE READ CAREFULLY SAFETY INSTRUCTIONS WARNING!:-To reduce the risk of severe injury or death Never let children operate or play with the doors controls Keep the remote control away from children . • Installation Instructions The GRD+ unit may be retrofitted to any roller doors including non Gliderol doors and also it does not require any disassembly of the door during installation. The GRD+ unit may be retrofitted to either side of a roller door. Selection of the desired side may be determined by the available room, location of power and general installation. • STOP WARNING: DO NOT ALLOW CHILDREN/PEOPLE AROUND THE DOOR WHEN PROPPED. SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE CAN RESULT FROM FAILURE TO FOLLOW THIS WARNING. D) Carefully loosen and remove the right hand spindle ‘U’ bolt e) Make sure the door supporting prop is secure. While the door is supported remove the right hand wall mount bracket.(Fig. • h) Replace right hand side wall mount bracket (Fig 4) Fig: 4a Fig: 4 Replace this picture showing G+ roller unit manual release. Fig: 5 i) Carefully remove the support from the door and rest spindle on the wall mount bracket j) Locate the Drive unit on the bracket and fit ‘U’. • Locate the weight bar on the centre of the bottom rail and drill two locating holes through the holes on the weight bar into the bottom rail. Secure the weight bar with two bolts provided. (Fig 6) Fig: 6 IMPORTANT: Security rivet / tek screw must always be applied to inner side of drum wheel as shown in Fig: 7a. Failure to do so may result in internal damage to the GRD drive unit. • PCB Index Motor Connector Hall Connector Transformer Connector Control Panel Connector Wireless Photocell Connector EAS Receiver Connector External Light Connector External I/O Terminal Glidermatic GRD+ Installation Instructions & owner’s manual Page 7. • User Interface MENU SETTING INDICATOR OPEN / MENU UP STOP / MENU ENTER CLOSE / MENU DOWN Transmitter Coding – By Controller 1. Press and hold [ENTER] for 2 seconds to enter menu selection 2. Using [UP] and [DOWN] to select Learn option, and press [ENTER] 3. Press and hold [ENTER] for 2 seconds to enter menu selection 2. Using [UP] and [DOWN] to select Key option, and press [ENTER] 3. [INDICATOR] will lit to show current key configuration 4. Using [UP] and [DOWN], select the desire transmitter key setting from the below options Single Button Configuration: Any one of the three buttons in the transmitter can be used to control all three functions Stop/Open/Close. Press and hold [ENTER] for 2 seconds to enter menu selection 2. Using [UP] and [DOWN] to select Limit option 3. To initiate door limit setting, and press [ENTER] 4. How to insert page number 1 starting on page 5 on mircosoft word 2008 for mac free. [INDICATOR] will lit to show current drive handing 5. Using [UP] and [DOWN], select the desire drive handing Left Hand Drive Right Hand Drive 6. • Force Setting 1. Press and hold [ENTER] for 2 seconds to enter menu selection 2. Using [UP] and [DOWN] to select Force option, and press [ENTER] 3. [INDICATOR] will lit to show current force configuration 4. ![]() Using [UP] and [DOWN], to adjust the force in the below manner Increase –. • LED Control Under 3 Keys transmitter mode, the LED can be switched on and off using the STOP key. This will also output to the EXTLIGHT terminal on-board. Vacation Mode Transmitter signal can be locked out by pressing STOP & CLOSE keys simultaneously and holding it for 3 seconds on the transmitter. • Photo Sensor Connection Diagram External Wall Switch Connection Diagram External Light Connection Diagram (Optional Interface Board Required) Glidermatic GRD+ Installation Instructions & owner’s manual Page 13. • Technical Specifications CHARACTERISTICS SYMBOL MIN. UNIT Input Voltage System Power Dissipation Transformer Power Transformer Output Voltage 21.6 26.4 Work Voltage of Motor MOTOR Lamp Power LED1~LED6 0.36 Buzzer Voltage Fuse FUSE Carrier Frequency Range Handset 389.9 390.1 Modulation Handset Deviation Handset. • Plug-in EAS Receiver (Optional) 1. Remove the LED lens and two screws 2. Lift up the control panel cover to find the PC board 3.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |